Big Bear Tools - Tormek Sharpening Machine and options

TORMEK

Call to Order (604) 987-2614 or Toll Free 1-877-454-8665 (TOOL)

TORMEK sharpening innovation from Sweden

Prolong the cutting efficiency of your edge tools by preventing any loss of temper in the steel with this ingenious water cooled sharpening system from Sweden!

Tormek T-7 Model
$707.99

Square Edge Jig
Tormek Square Edge Jig.
Convential jigs
Conventional jigs.
(Angle exaggerated for clarity.)
Safety stops
Safety stops (1) prevent the tool from sliding off the grindstone and scrape your knuckles.

Tormek T-7

The new T-7 model improves the accuracy and safety in edge tool sharpening thanks to two new innovations, a Square Edge Jig and a Truing and Dressing Tool with screw feed. These developments also make the sharpening more user friendly.

Conventional jigs on the market require that you align the tool in the jig with mounting screws which is time consuming and you lose the exact repeatability at each sharpening. The new Tormek Square Edge jig solves this problem and the chisel will be ground square, i.e. at 90 degrees, each time without any adjustments. This is achieved because the jig automatically aligns the chisel to its flat, machined face.

Another benefit is that the SE-76 can also clamp short and tapered tools firmly, e.g. Japanese chisels. The jig copes with blades up to 76 mm or 3" width.

The new Square Edge Jig SE-76 has safety stops, which prevent the tool from slipping off the stone, which can hurt your fingers.

The other development is a Truing and Dressing Tool TT-50 with screw feed. This enables the user to keep the stone in perfect condition, which is essential for a perfectly sharpened edge.

A seven year warranty applies to all customers including industrial users. This is possible due to the improved coating of the housing, stainless steel main shaft and a powerful, industrial AC motor, which is designed for continuous operation.

PDF T-7 leaflet (5.5 Megs)

The T-7 model has all the latest improvements

TT-50
Truing and Dressing Tool with screw feed
Trues the grindstone exactly round and flat. Guided by the Universal Support, which also guides the jigs. Dual knobs for smooth feed across the stone.

 
Stainless steel hardware
Stainless steel hardware
Prevents from rust and wear on bearings.
 

 
Universal support with acme thread
Universal support with acme thread
Round section without flat machining makes it faster to change position.

 
Improved horizontal base
Improved horizontal base
Double locking screws and tighter fit for highest precision.

 
Micro Adjust with scale
Micro Adjust with scale
For a predetermined cutting depth when using the TT-50 Truing and Dressing Tool.

 
7 year warranty
Valid also for industrial use.

 

The T-7 model is delivered with these accessories

SE-76
Square Edge Jig       		TT-50
Truing and Dressing Tool		 SP-650
Stone Grader		 WM-200
AngleMaster
PA-70
Honing Compound		 HB-10
Handbook		 DVD
Tormek DVD		  

Tormek T-7 Model
Available September 2007 - $707.99

 

 
 

TORMEK 2006 Machine - $539.99 Canadian

Tormek Sharpening System

Water Cooled Grinding Machine

With Grindstone, Leather Honing Wheel and Universal Support with micro adjust (US-105), which can be placed either vertically in sleeves or horizontally in the base XB-100.

Including:

• Straight Edge Jig SVH-60

• AngleMaster WM-200

• Honing Compound PA-70

• Handbook HB-10

• Instruction Video VID-4

 $539.99 Canadian
 
tormek system with details outlinedWet stone grinding with slow running speed gives you full control while grinding. The wheel will not shatter and there are no dangerous sparks with Tormek system. The quiet vibration-free industrial motor is rated for continuous operation, and the honing wheel has a coupling for fast removal.

With the Tormek System, you do BOTH the initial grinding (when you shape the tool and create the optimal edge angle) and the sharpening on the same grindstone. The grindstone can easily be changed from fast grinding to fine sharpening. The grinding/sharpening is carried out with water cooling, so there is no risk of burning the edge and drawing the hardening from the steel. The honing and polishing is carried out on a leather honing wheel.

Because of the exact repeatability, you remove very little material and therefore the sharpening is completed quickly. The result is that the lifetime of your tools is considerably prolonged.

Once you have ground your tool to the desired shape and edge angle, you can reproduce exactly the same shape with all future sharpenings-even difficult tools like fingernail turning gouges, spoon shaped woodcarving gouges and oval skew chisels with a curved edge.

The complete system includes

  1. Grinding stone
  2. New! Universal Support with micro adjust Foundation of the system.
  3. Horizontal Base for Universal Support
  4. Straight edge jig for plane irons and wood chisels.
  5. Genuine leather honing wheel for producing razor sharp edges
  6. Tube of honing compound
  7. The latest Edition handbook
  8. Tormek Instruction Video
  9. Pro AngleMaster-Sets any edge angle 15° - 75°

Additional System accessories are sold separately.

TNT-708 Woodturner’s Kit

This kit contains everything you need to shape and sharpen all your turning tools.

TNT-708
TNT-708 kit box

Contains

SVD-185

Gouge and Turning cutter Jig

For fingernail shaped bowl gouges and spindle gouges. Can be set to create the edge geometry of your choice. Also for exchangeable cutters of any shape.
SVS-50

Multi Jig

For skew chisel with a straight or a curved edge. Can be set for any skew angle. Even for skews with oval section. Also for parting and beading tools and roughing gouges.
TTS-100

Turning Tool Setter

For instant setting of the geometries on gouges and skews when using the SVD-185 and the SVS-50 jigs. With built in edge geometries. Works on any stone diameter.
SVD-110

Tool rest with TORLOCK

For scrapers, hollowing tools and thin parting tools. Secure locking on the Universal Support thanks to the patented design.
LA-120

Profiled Leather Honing Wheel

For honing and polishing the flute on gouges. With two exchangeable profiles. One with a 3 mm (1/8") radius and one with a 60° point.
MH-380

Machine cover

For protecting the machine from shavings and wood dust.

 
TNT-300

Woodturner’s Instruction Box

An 1 hour and 20 minutes comprehensive DVD made by Jeff Farris and a detailed handbook by Torgny Jansson shows how to best work with the Tormek TNT sharpening system.

Kit only

($347.99 Canadian) Without T-7 Machine.

Kit with Machine

($915.99 Canadian) Includes T-7 Model shown at the top.

HTK-705 Hand Tool Kit

This kit contains the jigs for sharpening your knives, scissors, draw knives and axes as well as short chisel and carving tools.

HTK-705
HTK-705 kit box

Contains

SVM-45

Knife Jig

For most knives. Width 45 mm (1 3/4"). Long knives need to be stiff. Min blade length 60 mm (2 3/8"). Also for carvers draw knives.
SVM-140

Long Knife Jig

Suitable for long and flexible knives. The 140 mm (5 1/2") width of the jig stabilizes a thin blade. Min blade length 160 mm (6 3/8").
SVX-150

Scissors Jig

For scissors of all sizes and shears. Also suitable for portable electric hand planer blades.
SVS-32

Short Tool Jig

For straight shanked carving gouges and V-tools down to 45 mm (1 3/4") length. Short wood chisels and tools for power carvers. Max. tool width 32 mm (1 1/4").
SVA-170

Axe Jig

For carving and carpenter's axes.
Max. axe size 170 mm (6 1/2").

 

 
 
 
 
 
 
 
 
 
Kit only

($191.99 Canadian) Without T-7 Machine.

Kit with Machine

($849.99 Canadian) Includes T-7 Model shown at the top.

Ultimate Kit

Includes the T-7 machine, the Jointer/Planer Blade Jig SVH-320 and both kit boxes

TNT-708 + HTK-705 + SVH-320
TNT-708   HTK-705   SVH-320
($1345.99 Canadian) Includes T-7 Model shown at the top.

Magnum Kit

Includes the T-7 machine and the two kit boxes.

TNT-708 + HTK-705
TNT-708   HTK-705

($1149.99 Canadian) Includes T-7 Model shown at the top.

 
 
Horizontal Base for Universal Support (XB-100)
($29.99 Canadian)

Switch from vertical base to horizontal base when you grind towards the edge, or when you need lower grinding pressure.

For upgrading earlier models.

Included with TORMEK 2006

 Stone Grader (SP-650) 

($31.99 Canadian) 

Grades the grinding stone to a fine grit in just 15 seconds. Also renews glazed stones.

Sold separately. 
Square Edge Jig (SE-76)

($62.99 Canadian)

The newest jig from Tormek perfectly aligns chisels and plane irons to a true grindstone. Grinding square edges on your tools has never been easier. It also has stops that prevent you from running off the edge of the grindstone. The capacity is a full 3 inches for even the largest plane irons.
Diamond Truing Tool (TT-50)

($91.99 Canadian)
 

The new TT-50 truing tool makes quick work out of re-cutting your grindstone parallel to the Universal Support and perfectly round. The screw feed mechanism moves the diamond cluster tip across the grindstone at a controlled pace for a uniform finish. The TT-50 is now included with the T-7. It will work on older model Tormek's as well.

Universal Support with Micro Adjust Universal Support with Micro Adjust(US-105)
 ($45.99 Canadian)

The universal support now incorporates a micro adjust so that you can more exactly and easily make the fine setting.

The new universal support has a chrome-nickel coating, which gives a harder surface with less friction.

Older machines can be upgraded by purchasing the new Universal Support separately.

Included with TORMEK 2006

 AngleMaster (WM-200)
($27.99 Canadian)

For setting and measuring any edge angle from 10° to 75°. For any stone diameter from Ø250 mm (10") down to Ø150 mm (6").

Included with TORMEK 2006
TORMEK HandbookTormek Sharpening Handbook
(HB-10E)
($35.99 Canadian)

Gives you detail in how to work with your Tormek system.

Included with TORMEK 2006

 Instructional DVD (DVD-1)
 ($16.20 Canadian) 

23 minutes detailing the set-up and operation of each jig and attachment in the TORMEK system. Chapter markers guide you to just the section you want to view when looking up a particular application. Included with each machine. Offered separately for owners who bought before the video was available or those who received the VHS and now want DVD, in case of loss, and for those of you who would like a look before you buy.
Honing Compound (PA-70) Honing Compound
($10.00 Canadian) 

For the leather honing wheels.

Included with TORMEK 2006

 Profiled Leather Honing Wheel (LA-120)
($67.99 Canadian)

With exchangeable leather discs. For inside honing and polishing of gouges and V tools. Mounts outside the standard leather honing wheel.

Sold separately.
Long Knife Jig (SVM-140)
($57.99 Canadian)  

Long Knife Jig
SVM-140   Same design as the SVM-45, but with a longer blade clamp for more stability on thin, flexible blades.
Turning Tool Setter (TTS-100)

($34.99 Canadian) 

Turning Tool Setter
TTS-100    Controlling complicated shapes on turning tools is as simple as 1-2-3 with the TTS 100 Turning Tool Setter. Set the protrusion to one of three stops, adjust the jig setting, and position the Universal Support using our patented two point contact method. It's all built into the TTS-100 -- even a printed reminder of the settings!
Woodturner's Instruction Box (TNT-300)

($35.99 Canadian)  

Woodturner's Instruction Box
TNT-300   Enjoy over an hour of video instruction on using your Tormek for turning tools, plus a bonus presentation on the fundamentals of turning. The companion book features nearly 200 detailed illustrations and step-by-step details on the correct approach to using the Tormek for turning tools. Both the book and video focus on our featured "Touch 'N' Turn" methods, which allow you to turn more and sharpen less!

Cabinet Maker's Apron (AN-04)

($40.45 Canadian)

With shoulder support, no pressure on your neck. Extra long tapes for all sizes. Special pockets with covers for your calculator, note pad, folding square, calliper and cellphone. 100 % cotton.

Sold separately 
Universal Gouge Jig (SVD-185)
($101.99 Canadian)  

Puts the edge back on V-and fingernail-shaped tools and gouges with a maximum of 1'' width. Also for turning cutters

Sold separately.

 Short Tool Jig (SVS-32)
($28.99 Canadian)

For straight shanked carving gouges and V-tools down to 1-3/4'' length. For short wood chisels and tools for power carvers. Max tool width 1-1/4''

Sold separately.
Tool Rest (SVD-110)
($38.99 Canadian)

For turning scrapers, cabinet scrapers, carving scorps and inshaves.

Sold separately.

 Axe Grinding Jig (SVA-170)
($19.99 Canadian)

For carving and carpenter's axes. Max. axe size 6-1/2''.

Sold separately.
Scissors Jig (SVX-150)
($55.99 Canadian)

Puts the maximum sharpness on all sizes of scissors and shears.

Sold separately.

 Planer/Joiner Blade Jig (SVH-320)
($197.99 Canadian)

Works with HSS blades of any length.

Sold separately.
Long Knife Jig (SVM-100)
($54.00 Canadian)

Gives greater stability on longer, thinner blades. Minimum blade length to be used with this jig is 4-23/32'' .

Sold separately.

 Knife Jig (SVM-45)
 ($41.99 Canadian) Knife Jig

Recommended for knives with a minimum blade length of 2-3/8''. Plus straight or curved spoke shave blades.

Sold separately.
Multi-Jig (SVS-50)
 ($70.99 Canadian)

For turning skew chisels, straight or radiused edge parting and beading tools and roughing gouges. Straight carving gouges up to 2'' width.

Sold separately.

 Moulding Knife Jig (SVP-80)
($179.99 Canadian)

Sharpens all makes and shapes of moulding knifes with 24, 30 or 38 mm distance between guide hole centres. Max width 100 mm (4"). Also for profiled paint removal blades.

Sold separately
Grinding Wheel for 2006 Wetstone grinder (SG250)
($191.99 Canadian)

Replacement Wheel for the above grinder. Size 250 mm x 50mm.

Aluminium Oxide for Wet Grinding

Sold separately

 Machine Cover (MH-380)
($27.99 Canadian)

Keeps your system free from dust and debris when not in use.

Sold separately.

Standard Profile Replacement Honing discs for the LA-120 (LA122)

($43.99 Canadian) 

Set of standard spare discs.
One with a 3mm (1/8") radius and one with a 60º tip.
 

Sold separately.

 

Optional Narrow Profile Honing discs for the LA-120 (LA124)

($43.99 Canadian) 

Set of optional, narrow discs. One with a 2mm
(3/32") radius and one with a 45º tip.
 

Sold separately.
Leather Honing Wheel LA-220

($74.99 Canadian) 

Replacement Leather Honing Wheel - You hone away the burr on the leather honing wheel impregnated with the TORMEK honing compound. The leather removes the burr gently like the barber's leather strop, giving you a razor sharpness and a bevel polished to a mirror finish. You can hone either free-hand or let the tool remain in the jig after the grinding, so that the honing is carried out at exactly the same angle as the previous grinding. For a tool, which has the right shape and edge angle but has become dull, you should go directly to the honing wheel. Since the tool is accurately guided in the jig, you can press on the tool without any risk of rounding off the bevel.

Blackstone Silicone Grinding Wheel SB-250

($215.99 Canadian) 

For hard materials and fast sharpening

Dia. 250mm x 50mm wide. Max 150 Rpm.

Japanese Waterstone Grinding Wheel SJ-250

($263.99 Canadian) 

For extra fine surface finish.

Dia. 250mm x 50mm wide. Max 150 Rpm.

  

 Call to Order (604) 987-2614
or
Toll Free 1-877-454-8665 (TOOL)